Ways to prevent an explosion of oil wells
You must follow these roads for the purpose of prevention of Alrvsh and prevent the explosion occurs:
You must fill in the well and monitored through withdrawals pipe where dictated every five Stanat.
Must monument inhibitors explosion before you start digging the container classes on gas, oil or water under high pressure.
You must remove any contamination of gas, oil or water from the drilling mud when it occurs.
You must constantly monitor the drilling mud when drilling in the oil layers and measure its properties.
You must control the level of the mud tanks.
Monument to measure the amount of gas mud devices (GAS DETECTOR) should also be set up to measure the amount of flow into the well devices (MUD FLOW INDICATOR).
You must provide a sufficient stock of bentonite clay materials and banner for the purpose of addressing the mud during the occurrence Alrvsh.
Measured by the amount of recycling pressure (CIRCULATION PRESSURE) before the Alrvsh movement when the pump speed (30 stroke / min) (SPM) and recorded daily in the drilling report when drilling exploratory wells.
How to control the well in the event of Alrvsh:
A must have recycling pressure (CIRCULATION PRESSURE) when pump action and quickly (30 stroke / min) (SPM) known before the Alrvsh and if not available use the following law to find it.
B - must stop the pump when feeling Balrvsh.
T - pulls the tube polygon (Kelly) to the top and then close the lightning blast and read Alamadgat read on the (stand pipe) It is advisable to open the throttle (chock) before closing the mind explosion and then gradually closed after the closure of mind blast.
W is added pressure when recycling pump action (30 strike / min) (SPM) before Alrvsh to read Alamadgat on the stand pipe (SIDP) where the result of the primary pressure.
C - the speed spins clay (30 stroke / min) (SPM) using the throttle (chock) and change the orifice so that the amount of primary constant pressure on Alamadgat on the stand pipe until it comes out all the contaminated mud.
H - increased mud weight to overcome the problem by taking the old weight plus the amount of the increase in the weight of the equation (SIDP) and taken in step (c).
G. When you infuse a new weight mud inside the pipe pressure change when Alamadgat in the stand pipe pressure from the primary to the final pressure until the arrival of the new mud to the end of the pipeline.
You must follow these roads for the purpose of prevention of Alrvsh and prevent the explosion occurs:
You must fill in the well and monitored through withdrawals pipe where dictated every five Stanat.
Must monument inhibitors explosion before you start digging the container classes on gas, oil or water under high pressure.
You must remove any contamination of gas, oil or water from the drilling mud when it occurs.
You must constantly monitor the drilling mud when drilling in the oil layers and measure its properties.
You must control the level of the mud tanks.
Monument to measure the amount of gas mud devices (GAS DETECTOR) should also be set up to measure the amount of flow into the well devices (MUD FLOW INDICATOR).
You must provide a sufficient stock of bentonite clay materials and banner for the purpose of addressing the mud during the occurrence Alrvsh.
Measured by the amount of recycling pressure (CIRCULATION PRESSURE) before the Alrvsh movement when the pump speed (30 stroke / min) (SPM) and recorded daily in the drilling report when drilling exploratory wells.
 |
| oil - petroleum |
A must have recycling pressure (CIRCULATION PRESSURE) when pump action and quickly (30 stroke / min) (SPM) known before the Alrvsh and if not available use the following law to find it.
B - must stop the pump when feeling Balrvsh.
T - pulls the tube polygon (Kelly) to the top and then close the lightning blast and read Alamadgat read on the (stand pipe) It is advisable to open the throttle (chock) before closing the mind explosion and then gradually closed after the closure of mind blast.
W is added pressure when recycling pump action (30 strike / min) (SPM) before Alrvsh to read Alamadgat on the stand pipe (SIDP) where the result of the primary pressure.
C - the speed spins clay (30 stroke / min) (SPM) using the throttle (chock) and change the orifice so that the amount of primary constant pressure on Alamadgat on the stand pipe until it comes out all the contaminated mud.
H - increased mud weight to overcome the problem by taking the old weight plus the amount of the increase in the weight of the equation (SIDP) and taken in step (c).
G. When you infuse a new weight mud inside the pipe pressure change when Alamadgat in the stand pipe pressure from the primary to the final pressure until the arrival of the new mud to the end of the pipeline.
